We have new PAL dumps from the following PCBs:
‘coolmod’ sent in dumps from two PAL20L8.Board is faulty so we are unable test GAL replacements but we assume dumps are good since devices were unsecured.Thanks to him.
I dumped a secured GAL20V8 and successfully reversed its equations onto a GAL22V10.
The Konami ‘056820’ is a custom IC in SIL package (13 pin with an unusual 2mm of pitch) used on GX System hardware:
Sometimes it’s wrongly reported to be an RGB DAC but if you look at his pinout (from Lethal Enforcers II schematics) you can understand it has a different function although always related to colors generation :
Its particular feature is that it gets extremely hot and may fail as a result.Here’s a picture taken from the net where the coating literally melted due excessive hot:
Driven by a curiosity I decided to take a look inside:
The biggest component in the upper left corner of the above picture is a Toshiba TA78M05F fixed voltage regulator, datasheet here:
https://www.jammarcade.net/files/Datasheets/TA78M05F.pdf.PDF
It provides on its output the +5V (regulating from +12V) to nearby custom ‘056766’ which is actually the DAC (specifically it powers the analog section of it since digital one takes the +5V from JAMMA connector).This explains why the part gets burning hot since the radiating surface of the heatsink (actually the copper of the PCB) is too small and not adequate in my opinion.All other parts are SOT-23 PNP transitors for amplify the RGB channels, capacitors (for decoupling and voltage regulator stability) and printed film resistors, in particular there are thre 75Ohm ones to bring the RGB signals to the standard impedance level.The custom was pretty easy to reproduce, the only precaution I took in design was to enlarge the heatsink surface on the footptint of the voltage regulator.I used an MC78M05 in DPAK package since the original part is nowadays obsolete :
https://www.jammarcade.net/files/Datasheets/MC78M00_series.PDF
This granted me a better heat dissipation.Here’s the assembled reproduction :
Testing on a Winning Spike:
See you to my next reproduction project!
The Konami ‘054573’ is a custom chip found on various PCBs from this manufacturer : Bucky O’ Hare, Metamorphic Force, Gaiapolis, Xexex, Mystic Warriors, Wild West C.O.W. Boys of Moo Mesa to name some.Technically speaking it’s a RGB DAC (one for each color) which converts into analog the palette data bits received from the the custom ASIC ‘054338’. There are no schematics showing it but it should be a 9-bit DAC .
It comes in the usual SIL package (15 pin) covered by black coating like many custom with similar functions :
I have partially covered this topic in a past repair from mine, where you can see also picture of its circuitry inside :
Gaiapolis & Metamorphic Force repair log (a.k.a Konami ‘054573″ color DAC reworking)
Being a important and not long reliable part I decided it was time to think of a replacement.No particular difficulties were encountered in identifying the internal parts, tracing connections and developing a PCB which arrived from my manufacturer after some time.Here’s the reproduction finally assembled and installed :
Testing on a Moo Mesa PCB was successful:
See you to my next reproduction project!
Some years ago I came across to a Rolling Thunder PCB where the custom marked ‘130’ was replaced by a small sub-board (don’t know if made from Namco or bootlegers, from manufacturing I presume the latter)
It seems the original custom is used only on Rolling Thunder PCB where, indeed, you can find it marked as ‘130’ in form of a DIP40 IC:
Whereas on schematics it’s shown as ’41’ like in Metrocross and Baraduke PCBs but it’s not the same and changes from game to game (the custom is basically an address decoder for generating the memory map which, indeed, is specific to a certain game)
After some time I sold the board but before doing this I took a couple of high-res scans of parts and solder side of this replacement PCB with the intention to reproduce it someday in a modern way.That’s what I successfully made recently :
I hope this will help to repair our Rolling Thunder PCBs with a faulty ‘CUS130’ as it seems it’s a quite prone to failure part.
Received from Portugal this Bucky O’ Hare PCB for repair:
Board was failing the POST all the time showing a ‘SOUND SYSTEM BAD’ message
The sound system was previoulsy reworked : the YM2151 was socketed
and the ‘054986A’ audio module had electrolytic capacitors replaced with thru-hole ones:
The solder side of the module showed signs of repairs too :
I suspected a broken trace underneath the module so I replaced it with a good one taken from a parts board.The error on POST changed to this :
I looked at the board and found that actually the device @C4 is the custom ‘054539’ while the one @C5 is 32k x 8-bit SRAM (whose data/address bus is connected to the custom)
Probing the RAM revealed that data lines were all stuck high:
Piggybacking it had no effect so most likely the ‘054539’ ASIC was bad.I removed it:
Soldered back a spare :
Board booted up fine and entered in game with no further issues.Another repair accomplished.
